• A Critical Review on Dissimilar Welding of Stainless Steels To Titanium Alloys: Technology and Metallurgy 

  Foroughi, Vahid؛ elmi hosseini, Reza (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  The jointment of titanium alloys to stainless steel poses significant challenges due to their substantially different physical, chemical, and thermal properties. The joint properties of 304 stainless steel and Ti6Al4V are ...

  ---

• Evaluation of Mechanical Properties and Corrosion Resistance in Welded Stainless Steel 321H: Influence of Buttering Techniques 

  Beigi, Masoud؛ Khosravifard, Ali؛ Rabiezadeh, Amin؛ Sani, Razieh (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  This study examines the mechanical properties and corrosion susceptibility of welded Stainless Steel 321H, focusing on the effects of buttering layers applied with NiCiMo filler metal compared to conventional welding without ...

  ---

• Production of Bio-Carbon Materials from Animal Manure That Can Be Used in Iron Reduction 

  Rabiei, Amin؛ Amini Najafabadi, Reza (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  The material obtained from cow manure is rich in carbon and has good heat capacity. Its characteristic feature is its predominantly cellulose composition. Research shows that the carbon contained in manure makes it usable ...

  ---

• Tribological Behavior of Weld Zone in TIG-Welded AISI410 Martensitic Stainless Steel 

  Rafiei, M.؛ Mostaan, H.؛ Bakhshandeh, A. R.؛ Ghaderi, S. (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  The influence of different filler metals on tribological properties of TIG-welded AISI410 steel was studied. The microstructure and tribological properties of the welded samples were detected via optical microscopy, scanning ...

  ---

• Improving the Steel Household Appliances Production Through Simulation and Gray Proximity Indexed Value 

  Seyedi, Seyed Hossein؛ Farhadi, Payam؛ Gharibi, Masoumeh؛ Seyedi, Seyed Mohammad (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  Improving the efficiency of the production process is one of the most critical goals for manufacturing companies to reduce costs and compete in the market. Identifying and resolving process bottlenecks is essential to ...

  ---

• Utilizing Gum Commiphora Mukul as Organic Binders to Replace Bentonite in Iron Ore Pelletizing 

  Koohestani, Hassan؛ Balooch, Ali؛ Hasanpoor, Jalal (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  The use of powdered concentrate in iron production reduces the furnace efficiency. As a result, the concentrate was converted into pellets. Bentonite is usually used as a binder in pellet production, posing several operational ...

  ---

• Aspen HYSYS Simulation of Reformer and Heat Recovery System 

  Mohsenzadeh, Fatemeh Mahnaz؛ Payab, Aida؛ Monazami Tehrani, Ghazaleh؛ Payab, Hassan (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  This research develops a simulation model for new design of reformer and heat recovery system (HRS) in the direct reduced of Khuzestan steel company in Iran. The endothermic reforming reactions in the reformer tubes, the ...

  ---

• Enhancing Atmospheric Corrosion Resistance of Shot-Peened A36 Steel in Humid Environments: The Impact of Carbon Monoxide and Surface Treatments 

  Shanaghi, Ali؛ Farrokhi, Amir (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  A36 steel is a widely used construction material, appreciated for its low carbon content and excellent weldability. However, it is prone to atmospheric corrosion, particularly in humid and polluted areas like Tehran with ...

  ---

• Investigation of Nitriding Effect on Cutting Vibration of Indexable End Mill During the Straight Groove 

  Rahi, Abbas؛ hossienpour, Mahdi؛ mahdikhani, behrouz؛ inanloo, elham (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  End-milling is a cutting technology that removes material from machined workpieces by end mill and is widely used to manufacture parts. Also, nitriding is a surface hardening process with a lot of effects on mechanical ...

  ---

• Investigation of the Effect of SiO2 Nanoparticles on Corrosion-Wear-Impact Resistance, and Bending Strength of Acrylic Coating Applied To Steel Substrate 

  Arzani, saeed؛ Pakzaman, Hamid (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-12-01)

  This study applied a nanocomposite coating to a plain carbon steel substrate using the air spray method. Various amounts of SiO2 nanoparticles (2-6%) were incorporated into the acrylic polymer-based coatings, and the results ...

  ---

• Investigation of Hydrate Formation Conditions of Simulated Flue Gas in TBAB Solution with Potential Application in CO2 Capture in Steel Industry 

  Yousefi, Sahebeh؛ Parsai Kia, َAli (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  The rising amount of CO2 in the atmosphere is one of the most urgent environmental issues of our age. In order to reduce anthropogenic CO2 emissions, carbon capture and storage (CCS) can be applied to large point sources ...

  ---

• Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack 

  Darbandi, Masoud؛ Fazeli, Masoud؛ Rashidi, Darioush؛ Basiriani, Behnam؛ Allahdadi, Masoud؛ Hosseinian, Seyyed Mohsen (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  This study uses the numerical simulation to successfully improve the performance of a subsonic ejector stack, which is used for the expulsion of flue gas in a Direct Reduction Iron unit located in Esfahan's Mobarakeh Steel ...

  ---

• Effects of CeO2 Flux and Shielding Gas In A-TIG Welding on The Microstructure, Corrosion and Passive Film of Super Duplex Phase Stainless Steel 2507 

  Ebrahimi, َAlireza؛ Guliani, Mehdi (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  This study explores using CeO2 flux with Ar and Ar+5%N2 shielding gases to enhance the welding process of 2507 super duplex stainless steel through active TIG welding. It discusses their impact on weld geometry, microstructure, ...

  ---

• Study on Vibration of Middle Leg in The MIDREX Shaft Furnace 

  Akhondizadeh, Mehdi؛ Bahaadini, Reza؛ Afsari, omid (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  In the present study, the vibration of the middle leg in MIDREX shaft furnace in Gol-Gohar Iron and Steel Development company (GISDCO) has been investigated to detect the cause of vibration. For this aim, field data-collection ...

  ---

• A Novel Approach for Estimating Fatigue Behavior of Stainless Steel 304 Using Tensile Test Data 

  Ebrahimi, R.؛ Reihanian, Mohsen؛ Namvarian, Raheleh (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  This paper introduces a novel method for estimating the fatigue behavior of stainless steel 304 through a single tensile test. By utilizing the engineering and true stress-strain curves, the constants of the Basquin equation ...

  ---

• Evaluation of Mechanical Properties of Welding ST-37 Steel Structures With Two Types of Welding Processes FCAW and SMAW 

  mohammadi soleymani, moslem؛ Mehrabi Gohari, Ehsan؛ zahedian, alireza (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  ST-37 steel is applied in the construction of steel structures due to its good strength, toughness, and high weldability. In this study, two samples of ST-37 steel joint were prepared using E71T filler metal by FCAW powder ...

  ---

• Using Recycled Machining Chips and Reduced Graphene Oxide in Spot Welding of Galvanized Sheets to Improve Hardness and Corrosion Resistance 

  Sedehi, Sayyed Mohammad Reza؛ Yazdi, Sayyed Hashem؛ Norouzi Palangani, Fatemeh؛ Maleki, Zahra؛ Poudinehei, Rahele (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  In recent years, spot welding has received increasing attention from metal sheet-related industries due to its efficiency, high speed, and low operational costs. This study aims to enhance the spot welding properties of ...

  ---

• Microstructure and Corrosion Behavior of Friction Stir-Welded DP600 Steel 

  Ashrafi, Hamid؛ Mohammadi, Majid (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  This study examined the microstructure and corrosion characteristics of friction stir welded DP600 steel. Two different combinations of rotational and transverse speeds were used for the welding process: 700 rpm and 80 ...

  ---

• Morphological Investigation of Al-Cu-Fe Quasi-Crystalline Thin Film on Ti-6Al-4V Alloy 

  Rahimipour, Mohammad Reza؛ Abaei, Mohsen؛ Farvizi, Mohammad؛ Eshraghi, Mohammad Javad (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  Magnetron sputtering was used in the current study to deposit the quasicrystal (QC) coating on the Ti-6Al-4V alloy. After the sputtering process, a continuous argon flow at 700°C was used for two hours to anneal the Al-Cu-Fe ...

  ---

• Isothermal Kinetic Analysis of Dissolution of The Retained Delta Ferrite in AISI 304 Stainless Steel During Homogenization 

  Aghebatkheiri, fatemeh؛ Mashreghi, Alireza؛ Hasani, ُSaeed (Iron & Steel Society of Iranانجمن آهن و فولاد ایران, 2024-11-01)

  In this investigation, the dissolution kinetics of delta ferrite in AISI-304 austenitic stainless steel during homogenization was studied. The study encompasses a temperature range of 1050 to 1250 °C (1523 K) and a time ...

  ---

View more