• ثبت نام
    • ورود به سامانه
    مشاهده مورد 
    •   صفحهٔ اصلی
    • نشریات انگلیسی
    • International Journal of Engineering
    • Volume 31, Issue 8
    • مشاهده مورد
    •   صفحهٔ اصلی
    • نشریات انگلیسی
    • International Journal of Engineering
    • Volume 31, Issue 8
    • مشاهده مورد
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Preliminary Characterization of Corn Cob Ash as an Alternative Material for Ceramic Hollow Fiber Membrane (CHFM/CCA)

    (ندگان)پدیدآور
    Kamarudin, N. HHarun, ZOthman, M. H. DHubadillah, S. KJamaluddin, M. RYusof, K. N
    Thumbnail
    دریافت مدرک مشاهده
    FullText
    اندازه فایل: 
    1.449 مگابایت
    نوع فايل (MIME): 
    PDF
    نوع مدرک
    Text
    زبان مدرک
    English
    نمایش کامل رکورد
    چکیده
    Currently, exchanging trends in the expensive usage of ceramic materials such as alumina, zirconia etc. into economical ceramic raw sources have been studied extensively over the last decade for various technological applications. Despite the fact that this ceramic compound or elements offer a great performance and stability, especially at high temperature and corrosive or acidic conditions, the basic commercial price of this compound which is a little bit higher have hindered the used of these materials. Thus interest in fabricating of bio-ceramic membrane using corn cob ash, an agricultural by product not only offered the development of new low cost materials but also able to enhance better properties and performance. The suitability of corn cob ash as an alternative material for ceramic hollow fiber membrane fabrication (CHFM/CCA) as a main substrate was investigated via combined phase inversion and sintering technique based on several controlled operating parameters. The effects of selected bore fluid (5, 10, 15 and 20 mL/min) and different sintering temperature (800˚C, 900˚C, 1000˚C, 1100˚C) towards membrane structure and properties were observed and studied. Interestingly, analysis of the SEM morphology showed that the potential of the main constituents of corn cob ash which highly consisted of silica, alumina and calcium oxide are able to improve the properties of CHFM/CCA by lowering sintering temperature (1000˚C) as compared to the standard CHFM bodies which normally has sintering temperature higher than 1200 ºC. Thus, the used of corn cob ash not only able to enhance better ceramic properties but also able to reduce sintering temperature. Reduction in energy consumption with slightly reduced sintering temperature also will offer a better sustainable process through recycling abundant waste materials as well as the emphasis on the green resources. In respect, the bio-material of corn cob ash is capable to replace the commercial ceramic membrane materials for membrane applications by considering the availability of this agro waste product as the main crops in most countries in the world.
    کلید واژگان
    green corn cob ash
    ceramic hollow fiber membrane
    reduced sintering temperature

    شماره نشریه
    8
    تاریخ نشر
    2018-08-01
    1397-05-10
    ناشر
    Materials and Energy Research Center
    سازمان پدید آورنده
    Integrated Material and Process, Advanced Manufacturing and Material Center (AMMC), Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia
    Integrated Material and Process, Advanced Manufacturing and Material Center (AMMC), Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia
    Advanced Membrane Technology Research Centre (AMTEC), Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
    Advanced Membrane Technology Research Centre (AMTEC), Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
    Integrated Material and Process, Advanced Manufacturing and Material Center (AMMC), Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia
    Integrated Material and Process, Advanced Manufacturing and Material Center (AMMC), Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia

    شاپا
    1025-2495
    1735-9244
    URI
    http://www.ije.ir/article_73259.html
    https://iranjournals.nlai.ir/handle/123456789/337371

    مرور

    همه جای سامانهپایگاه‌ها و مجموعه‌ها بر اساس تاریخ انتشارپدیدآورانعناوینموضوع‌‌هااین مجموعه بر اساس تاریخ انتشارپدیدآورانعناوینموضوع‌‌ها

    حساب من

    ورود به سامانهثبت نام

    آمار

    مشاهده آمار استفاده

    تازه ترین ها

    تازه ترین مدارک
    © کليه حقوق اين سامانه برای سازمان اسناد و کتابخانه ملی ایران محفوظ است
    تماس با ما | ارسال بازخورد
    قدرت یافته توسطسیناوب