• Mechanical Characterization of Glass-Basalt-Carbon/Polyester Hybrid Composites 

  El-Wazery, M. S (Materials and Energy Research Center, 2018-07-01)

  Influence of the stacking sequences of hybrid composites on the tensile strength, flexural strength, inter-laminar shear strength (ILSS) and impact energy was investigated. The hybrid glass-basalt-carbon/polyester composite ...

  ---

• Parametric Optimization of Electro Spark Microwelding of Aluminum Clad Steel (RESEARCH NOTE) 

  Rastkerdar, E؛ Aghajani, H؛ Kianvash, A؛ Sorrell, C. C (Materials and Energy Research Center, 2018-07-01)

  The feasibility and parameters optimization of AA5183 aluminum cladding on AISI 1018 steel by electro spark microwelding (ESM) and the corrosion resistance of the clad plate were investigated. The optimum conditions were ...

  ---

• Investigation of the Fractional Composition Effect of the Carbonate Weighting Agents on the Rheology of the Clayless Drilling Mud 

  Morenov, V؛ Leusheva, E؛ Martel, A (Materials and Energy Research Center, 2018-07-01)

  The article considers the issue of reducing the influence of clayless mud components on the filtration parameters of the reservoir. In the composition of such solutions, calcium carbonate of various fractions is often added ...

  ---

• Mechanical Surface Treatments of Ti-6Al-4V Miniplate Implant Manufactured by Electrical Discharge Machining (TECHNICAL NOTE) 

  Qosim, N؛ Supriadi, S؛ Puspitasari, P؛ Kreshanti, P (Materials and Energy Research Center, 2018-07-01)

  Present work aims at multi-mechanical surface treatment of Ti-6Al-4V based-miniplate implant manufactured by electrical discharge machining (EDM) for biomedical use. Mechanical surface treatment consists of consequent use ...

  ---

• Numerical Analysis of Fully Developed Flow and Heat Transfer in Channels with Periodically Grooved Parts (TECHNICAL NOTE) 

  Joodaki, A (Materials and Energy Research Center, 2018-07-01)

  To obtain a higher heat transfer in the low Reynolds number flows, wavy channels are often employed in myriad engineering applications. In this study, the geometry of grooves shapes is parameterized by means of four angles. ...

  ---

• Finite Plate with Circular and Square Hole under Partial Loading 

  Dehghani, M (Materials and Energy Research Center, 2018-07-01)

  In this paper a general analytical solution is obtained to find stress distribution in a finite elastic plate with a circular or square hole subjected to arbitrary biaxial partial loading using modified boundary condition ...

  ---

• Effect of Different Nanoparticles and Friction Stir Process Parameters on Surface Hardness and Morphology of Acrylonitrile Butadiene Styrene 

  Mamaghani Shishavan, S؛ Azdast, T؛ Mohammadi Aghdam, K؛ Hasanzadeh, R؛ Moradian, M؛ Daryadel, M (Materials and Energy Research Center, 2018-07-01)

  In the present study, the effect of material and process parameters on the morphological and hardness properties of friction stir process (FSP) acrylonitrile butadiene styrene (ABS) were investigated. For this purpose, ...

  ---

• Ovality and Bow Defect of Pre-punched Sheets in Roll Forming of Trapezoidal Sections 

  Safari, M؛ Joudaki, J (Materials and Energy Research Center, 2018-07-01)

  Roll forming process is used for manufacturing sheet metal parts by successive bending and creating the final shape with gradual deformation. In this article, deformation of a pre-punched sheet due to the roll forming ...

  ---

• Vibration Behavior of Nanocomposite Plate Reinforced by Pristine and Defective Graphene Sheets; an Analytical Approach 

  Allahyari, E؛ Asgari, M (Materials and Energy Research Center, 2018-07-01)

  Free vibration characteristics of polymer composite plates reinforced by graphene nanosheets employing the Eringen nonlocal elasticity theory were investigated. Theoretical formulations are derived based on Hamilton's ...

  ---

• Toward an Improvement of Natural Gas-diesel Dual Fuel Engine Operation at Part Load Condition by Detail CFD Simulation 

  Khatamnejad, Hassan؛ Khalilarya, S؛ Jafarmadar, S؛ Mirsalim, M؛ Dahodwala, M (Materials and Energy Research Center, 2018-07-01)

  Natural gas-diesel dual fuel combustion is a beneficial strategy for achieving high efficient and low emissions operation in compression ignition engines, especially in genset application heavy duty diesel engine at rated ...

  ---

• A Procurement-distribution Coordination Model in Humanitarian Supply Chain Using the Information-sharing Mechanism 

  Nikkhoo, F؛ Bozorgi-Amiri, A (Materials and Energy Research Center, 2018-07-01)

  The coordination problem of relief items' distribution operations is essential in humanitarian relief chains. If the coordination is proper, it will improve the response phase to the crisis. In order to improve the ...

  ---

• Evaluation of Mechanical and Tribological Properties of Glass/Carbon Fiber Reinforced Polymer Hybrid Composite 

  Jesthi, D. K؛ Nayak, A؛ Routara, B. C؛ Nayak, R. K (Materials and Energy Research Center, 2018-07-01)

  Polymer matrix composites used in different industrial applications due to their enhanced mechanical properties and lightweight. However, these materials are subjected to friction and wear situations in some industrial and ...

  ---

• Position Control Improvement of Permanent Magnet Motor Using Model Predictive Control 

  Arehpanahi, M؛ Fazli, M (Materials and Energy Research Center, 2018-07-01)

  Fast and accurate transient response is the main requirement in electric machine position control. Conventional cascade control structure has sluggish response due to the limitation of inner control loop bandwidth. In this ...

  ---

• An Accurate 2D Analytical Model for Transconductance to Drain Current ratio (gm/Id) for a Dual Halo Dual Dielectric Triple Material Cylindrical Gate All Around MOSFETs 

  Gupta, N؛ Patel, J. K. B؛ Raghav, A. K (Materials and Energy Research Center, 2018-07-01)

  A dual-halo dual-dielectric triple-material cylindrical-gate-all-around/surrounding gate (DH-DD-TM-CGAA/SG) MOSFET has been proposed and an analytical model for the transconductance-to-drain current ratio (TDCR) has been ...

  ---

• Design Optimization of Axial Flux Surface Mounted Permanent Magnet Brushless DC Motor For Electrical Vehicle Based on Genetic Algorithm 

  Patel, A. N؛ Suthar, B. N (Materials and Energy Research Center, 2018-07-01)

  This paper presents the design optimization of axial flux surface mounted Permanent Magnet Brushless DC motor based on genetic algorithm for an electrical vehicle application. The rating of the motor calculated form vehicle ...

  ---

• Eulerian Lagrangian Simulation of Particle Capture and Dendrite Formation on Binary Fibers 

  Akbarnezhad, S؛ Soltani Goharrizi, A؛ Salmanzadeh, M (Materials and Energy Research Center, 2018-07-01)

  The capture efficiency of the small aerosol particle is strongly influenced by the structure of fibrous layers. This study presents particle deposition and dendrite formation on different arrangements of binary fibers. 2-D ...

  ---

• Combine Use of Fly Ash and Rice Husk Ash in Concrete to Improve its Properties (RESEARCH NOTE) 

  Kanthe, V؛ Deo, S؛ Murmu, M (Materials and Energy Research Center, 2018-07-01)

  This research paper describes the study of combined effect of Fly Ash (FA) and Rice Husk Ash (RHA) on properties of concrete as partial replacement of Ordinary Portland Cement (OPC). These by-products are having high ...

  ---

View more