• ثبت نام
    • ورود به سامانه
    مشاهده مورد 
    •   صفحهٔ اصلی
    • نشریات انگلیسی
    • Iranian Journal of Materials Forming
    • Volume 2, Issue 1
    • مشاهده مورد
    •   صفحهٔ اصلی
    • نشریات انگلیسی
    • Iranian Journal of Materials Forming
    • Volume 2, Issue 1
    • مشاهده مورد
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Interaction Between Precipitation and Dynamic Recrystallization in HSLA-100 Microalloyed Steel

    (ندگان)پدیدآور
    Ebrahimi, Gholam rezaMomeni, AmirEskandari, Hamid
    Thumbnail
    دریافت مدرک مشاهده
    FullText
    اندازه فایل: 
    350.6کیلوبایت
    نوع فايل (MIME): 
    PDF
    نوع مدرک
    Text
    Research Paper
    زبان مدرک
    English
    نمایش کامل رکورد
    چکیده
    Strain induced precipitation in HSLA-100 steel was investigated by conducting hotcompression and relaxation tests at temperature range of 850°C to 1100°C and strain rate of 0.001s-1 to 1s-1. The absence of dynamic recrystallization at temperatures below 1000°C was attributedto the influence of dynamic precipitation. The stress relaxation tests showed that strain inducedprecipitation is possible over a wide range of temperatures from 850°C to 1050°C. The startingand finishing times of precipitation were sensitive to temperature than strain rate. At temperaturerange of 950-1000°C and strain rate of 0.1s-1 the lowest times for precipitation were observed. Thecombination of precipitation-time-temperature and recrystallization-time temperature diagramsshowed that at high temperatures and low strain rates, precipitation precedes dynamicrecrystallization, whereas at the opposite condition, dynamic recrystallization goes in advance. Thestarting and finishing times for dynamic precipitation were approximated about 40 percent lowerthat those for strain induced precipitation.
    کلید واژگان
    Hot deformation
    Cu-bearing HSLA steel
    Dynamic recrystallization
    Hot compression
    Stress relaxation

    شماره نشریه
    1
    تاریخ نشر
    2015-04-01
    1394-01-12
    ناشر
    Shiraz University
    سازمان پدید آورنده
    Department of Materials and Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran
    Department of Materials Science and Engineering, Hamedan University of Technology, Hamedan, Iran
    Department of Civil Engineering, Faculty of Engineering, Hakim Sabzevari University, Sabzevar, Iran

    شاپا
    2383-0042
    URI
    https://dx.doi.org/10.22099/ijmf.2015.2914
    http://ijmf.shirazu.ac.ir/article_2914.html
    https://iranjournals.nlai.ir/handle/123456789/325260

    مرور

    همه جای سامانهپایگاه‌ها و مجموعه‌ها بر اساس تاریخ انتشارپدیدآورانعناوینموضوع‌‌هااین مجموعه بر اساس تاریخ انتشارپدیدآورانعناوینموضوع‌‌ها

    حساب من

    ورود به سامانهثبت نام

    آمار

    مشاهده آمار استفاده

    تازه ترین ها

    تازه ترین مدارک
    © کليه حقوق اين سامانه برای سازمان اسناد و کتابخانه ملی ایران محفوظ است
    تماس با ما | ارسال بازخورد
    قدرت یافته توسطسیناوب